Installation and Operation Manual Gas Cooktops Series RN8200G RN8400G RN8600G RN8800G Date Purchased Serial Number Dealer Service Provider 228605
8 Dimensions Leg Stand Models RN8200G Models - not available in Leg Stand Base option. RN(L)8400G-LS Refer to Page 9 for Cooktop options = Rating Pla
9 Dimensions Refrigerated Base Models RN8200G and RN8400G Models - not available in Refrigerated Base option. RN(L)8600G-RB RN(L)8800G-RB Refer to Pag
10 Dimensions Cooktop Options RN(L)8200G RN(L)8400G RN(L)8800G RN(L)8803G RN(L)8806G RN(L)8809G RN(L)8600G RN(L)8603G RN(L)8606G RN(L)8609G RN(L)8203G
11 Installation Installation Requirements NOTE: It is most important that this Cooktop is installed correctly and that operation is correct before
12 Installation Clearances NOTE: Only non-combustible materials can be used in close proximity to this appliance. * Side clearances can be 50mm when
13 Installation Rear Adjustable Feet, fitting:- a. Secure rear of base tray to rear cooktop legs by screwing the two adjustable feet supplied, into ba
14 Installation Fitting Adjustable Feet / Rear Rollers to Cabinet and Refrigeration Bases. Rear Adjustable Feet, fitting:- 1. Raise appliance from flo
15 Installation Gas Connection NOTE: ALL GAS FITTING MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON. 1. Waldorf Cooktops do not require electrical co
16 Installation Commissioning 1. Before leaving the new installation; a. Check the following functions in accordance with operating instructions speci
17 Operation Operation Guide 1. Waldorf appliances have been designed to provide simplicity of operation and 100% safety protection. 2. Improper opera
MANUFACTURED BY Moffat Limited Christchurch New Zealand
18 Operation Open Burners ('F' - Flame Failure Option) Lighting the Open Burners Flame Failure Protection is incorporated for each burner b
19 Operation Griddle Lighting the Griddle a. Depress gas control knob and rotate anti-clockwise to ‘PILOT’ position. b. Hold gas control knob depress
20 Cleaning and Maintenance Before Commencing Cleaning NOTE: Allow appliance to cool before commencing cleaning. DO NOT use abrasive or strong ca
21 Cleaning and Maintenance Open Burner Cleaning 1. Remove pot stands, burner caps, burner bowls and pot stand supports from top of cooktop. Wash wit
22 Fault Finding This section provides an easy reference guide to the more common problems that may occur during operation of your equipment. The fau
23 Gas Conversion and Specifications Conversion Procedure NOTE: These conversions should only be carried out by qualified persons. All connect
24 Gas Conversion and Specifications Griddle 1. Carry out the following:- Remove griddle plate section and heat shield. Remove main burner. Disc
25 Gas Conversion and Specifications Gas Regulator - NAT Gas / LPG / Butane Only. NOTE: The gas regulator supplied is convertible between Natural Ga
26 Gas Conversion and Specifications Gas Specifications - Australia - New Zealand - United Kingdom Category: II2H3P (20, 37). Flue Type: A1. N
27 Gas Conversion and Specifications - All Other Markets NOTE: (*) Measure Burner operating pressure at manifold test point with two burners op
Contents Waldorf Gas Cooktops RN(L)8200G Gas Cooktop 300mm wide. RN(L)8400G Gas Cooktop 600mm wide. RN(L)8600G Gas Cooktop 900mm wide. RN(L)8800G Gas
28 Replacement Parts List Replacement Parts List When ordering replacement parts, please quote part number and description as listed below. If part
29 Replacement Parts List General 227015 Pot Stand. 228881 Spill Tray 300mm (RN8200G Series). 228882 Spill Tray 600mm (RN8400G / RN8800G Series). 2288
2 Introduction We are confident that you will be delighted with your WALDORF GAS COOKTOP, and it will become a most valued appliance in your commercia
3 Specifications Model Numbers Covered in this Specification RN[1]8200G-[2]-[3] 2 Open Burners. RN[1]8203G -[3] 300mm Griddle. RN[1]8400G-[2]-[3]
4 Specifications Gas Supply Requirements - Australia - New Zealand - United Kingdom Category: II2H3P (20, 37). Flue Type: A1. * - Measure burner
5 Specifications - All Other Markets NOTE: (*) Measure Burner operating pressure at manifold test point with two burners operating at 'High
6 Dimensions Bench Models Refer to Page 9 for Cooktop options = Rating Plate Location for this option. R RN(L)8400G-B RN(L)8200G-B R RN(L)8600G-B RN(
7 Dimensions Cabinet Base Models RN8200G Models - not available in Cabinet Base option. RN(L)8400G-CB RN(L)8600G-CB R = Rating Plate Location for thi
Komentáře k této Příručce