1 Installation and Operation Manual FN8120GE FN8226GE FN8130GE ‘Fast-Fri’ Gas Fryer Electronically Controlled Date Purchased Serial Number Dealer
8 Dimensions FN(L)8130GE
9 Installation Installation Requirements NOTE: • It is most important that this Fryer is installed correctly and that the operation is correct before
10 Installation 4. All air for burner combustion is supplied from underneath the appliance. The legs must always be fitted and no obstructions place
11 Installation Fitting Rear Rollers. 1. Raise the appliance from the floor by approx. 75mm using suitable lifting equipment (i.e. Palletiser / Forkl
12 Installation NOTE: A Manual Isolation Valve must be fitted to the individual appliance supply line. 3. Correctly locate the appliance into its f
13 Installation Electrical Connection NOTE: ALL ELECTRICAL CONNECTION MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON. 1. Each appliance should be c
14 Operation Operation Guide 1. WALDORF 'FAST-FRI' fryers have been designed to provide simplicity of operation and 100% safety protection.
15 Operation Description of Controls A commercial heavy duty, gas fired Fryer using a fast fry infra red burner system and is available in 3 model typ
16 Operation Twin Tank FN 8226GE Controls Single Tank FN 8130GE Controls Flame Failure Button Gas Control Knob Left & Ri
17 Operation Description of the Electronic Control Panel Control Panel Functions Each control panel comprises the following:- One 4 digit, seven segm
2 The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in writing by the
18 Operation Operation of the Appliance NOTE: For Controller Programming details refer to the ‘Controller Programming’ section at the rear of this m
19 Operation 5. When the appliance displays ‘droP’ this indicates that the Fryer is ready to commence cooking operations. 6. If there is a “.” displ
20 Operation Filling the Tank(s) NOTE: WALDORF 'FAST-FRI' fryers can be used with both oil and shortening. 1. Before filling the tank, al
21 Operation FN8130GE Fryer (Single Tank) 1. With the fryer tank full of frying medium, the pilot burners can be lit. 2. Check that the gas supply i
22 Operation Turning ‘OFF’ the Fryer To the ‘Pilot’ Position a. Depress and rotate the gas control valve clockwise to the ‘Pilot’ position. b. The m
23 Operation Frying Temperature Guide and Care of Frying Medium Summary of Practical Care of Frying Fats and Oils Fats and oils are unstable compounds
24 Cleaning and Maintenance General • To achieve the best results cleaning must be regular and thorough and all controls and mechanical parts checked
25 Cleaning and Maintenance Daily Cleaning 1. At the end of each day or at the end of each shift, if the frying schedule is heavy, the frying medium
26 Cleaning and Maintenance Weekly Cleaning NOTE: If the fryer usage is very high, we recommend that the weekly cleaning procedure is carried out on
27 Fault Finding Fault Possible Cause Remedy Frying medium foaming. Presence of soap or detergent residue from cleaning the tank. Rinse the fryer t
Contents FN(L)8120GE ‘FAST FRI’ GAS FRYER (Single Tank - 20Ltr) FN(L)8226GE ‘FAST FRI’ GAS FRYER (Twin Tank - 26Ltr) FN(L)8130GE ‘FAST FRI’ GAS
28 Fault Finding Fault Possible Cause Remedy Rapid oil breakdown. Inadequate frying oil turnover. Adjust procedures to fry more food in the fryer
29 Fault Finding Fault Possible Cause Remedy Pilot Burners will not light / stay alight. Check gas supply is turned on. Turn on gas supply. Check g
30 Fault Finding Fault Possible Cause Remedy Over temperature Thermostat cuts out the Pilot Burners. Overtemperature thermostat is faulty. If thermo
31 Wiring Schematics FN8120GE / FNL8120GE Fryer Schematic T/CFLAME FAILURE VALVESIT M1/AMAIN GAS CONTROLSIT NOVA 820mV24V 50HzTHERMOSTATOVER TEMPIGNIT
32 Wiring Schematics FN8226GE / FNL8226GE Fryer Schematic THMAIN GAS CONTROLSIT NOVA 820mV24v 50HzMAIN GAS CONTROLSIT NOVA 820mV24v 50HzPILOT PILOTT/C
33 Wiring Schematics FN8130GE / FNL8130GE Fryer Schematic T/CFLAME FAILURE VALVESIT M1/AMAIN GAS CONTROLSIT NOVA 820mV24V 50HzTHERMOSTATOVER TEMPIGNIT
34 Controller Basic Programming Mode Controller Basic Programming Mode: NOTE: • 'Timer 1', 'Timer 2' and ‘Timer 3' keys on e
35 Controller Basic Programming Mode Programming the Timers 1. To change the settings, press either 'Timer 1 - Up’ key or 'Timer 3 - Down&a
36 Controller Basic Programming Mode Programming the 'Temperature' 1. The stored set ‘Temperature’ is displayed (default 350°F - 176.5°C) w
37 Controller Advanced Programming Mode With mains power to the fryer turned ‘On’, press the ‘ON / OFF’ key to turn ‘On’ the appliance. 1. Enter t
Contents Contents Controller Basic Programming Mode ... 34 Programming the Password Protection. Prog
38 Controller Advanced Programming Mode Temperature Display Mode The temperature display can be set for two temperature display modes:- 't -1’
39 Controller Advanced Programming Mode Setting the ‘Temperature Units’. 14. The user may select from ‘F’ (Fahrenheit) or ‘C’ (Celsius). 15. To ch
40 Gas Conversion and Specifications Conversion Procedure NOTE: • These conversions should only be carried out by qualified service persons. All con
41 Gas Conversion and Specifications Main Burner Injectors 1. Unscrew and remove the main burner injectors (12.7 mm A/F) located in front of main bur
42 Gas Conversion and Specifications Gas Type Identification Label On completion of the gas conversion, replace the 'Gas Type Identification Labe
43 Replacement Parts Replacement Parts List When ordering spare parts, please quote the part number and the description as listed below. If the part
44 Replacement Parts General 018019 Basket. 227856 Door Magnet. 227451 Door Handle. (FN8120GE / FN8226GE). 227460 Door Handle. (FN8130GE). 018358 D
3 Introduction We are confident that you will be delighted with your Waldorf ‘Fast-Fri’ Gas Fryer and it will become a most valued appliance in your c
4 Specifications Model Numbers Covered in this Specification FN[1]8120GE ‘FAST FRI’ GAS FRYER (Single Tank - 20Ltr). FN[1]8226GE ‘FAST FRI’ GAS FR
5 Specifications Gas Connection Non UK Models Only: FN(L)8120GE Gas supply connection point is located 151 mm from the left hand side, 36 mm from the
6 Specifications Electrical Supply Requirements 220 -240Vac, 1P+N+E, 50Hz, 0.5A. Electrical Connection FN(L)8120GE Electrical supply entry point is l
7 Dimensions FN(L)8120GE FN(L)8226GE
Komentáře k této Příručce